Vennligst vent...
Produktet ble lagt i handlekurven. Se handlekurven her

Sharp / NEC NEC MultiSync UN552S 55inch UN-Series large format display for videowalls 700cd/m2 Direct LED backlight 24/7 proof OPS Slot CM Slot

Forsiden Skjerm og Projektor Public Displays 52-65" Sharp / NEC NEC MultiSync UN552S 55inch UN-Series large format display for videowalls 700cd/m2 Direct LED backlight 24/7 proof OPS Slot CM Slot
Du må logge inn for å handle/se priser.
Sharp / NEC NEC MultiSync UN552S 55inch UN-Series large format display for videowalls 700cd/m2 Direct LED backlight 24/7 proof OPS Slot CM Slot (60004523)

Sharp / NEC NEC MultiSync UN552S 55inch UN-Series large format display for videowalls 700cd/m2 Direct LED backlight 24/7 proof OPS Slot CM Slot

Varenr.:
60004523
EAN:
5028695115514
  • Skjermstørrelse 55"
  • Oppløsning 1920 x 1080
  • HD Full HD
  • USB-C 0
  • DVI 1
  • DP 3
  • HDMI 3
  • VGA 0
  • Berøringsskjerm Nei
  • Høyttalere Nei
  • 3D Nei
  • Skjermform Flat
  • Høydejustering Nei
  • Svivel Nei
  • Svingtapp Ja
  • Bruksområde Digital signage
Forventet på lager 07.02.2023
Beskrivelse

UN552S


The use of an ultra-narrow bezel* and accurate colour reproduction enable a beautiful and natural large-screen display

The ultra-narrow bezel that makes the boundary line of the screen less conspicuous
The non-display area (top, bottom, left, and right) of the UN552S/UN552VS is only 0.44 mm** in width. The ultra-narrow bezel makes the boundary line of the screen less conspicuous even in a multiscreen configuration and enables a natural display similar to a single image.

Enhanced calibration before shipping reduces installation time
Colour calibration that covers brightness and colour irregularities on the screen at each step of manufacturing means uniform colour reproduction when screens are installed together. Easily noticeable colour variations in areas where screens meet has been reduced when compared with existing products.
Furthermore, even in the case of colour calibration settings based on your colour sensors, calibration can be finished in an even shorter time.

When there is a change to a different colour setting, the image colour can be configured without colour variations by an on-screen display operation via the remote control.
This is intended to reduce the colour matching time compared to calibration using a colour sensor. Furthermore, the display is equipped with various colour conversion functions, such as emulation of representative colour spaces*.

Reduce colour variation between screens due to long-term use
Screen colour changes that advance with temperature changes and long-term use are corrected automatically by a built-in sensor and the SpectraView Engine colour correction function. They maintain stable performance and reduce the burden of complicated calibration work. The UX series models are equipped with a backlight sensor for even more advanced correction.

Based on the screen state after irregularity correction was performed before shipping, the areas around the four corners of the screen where colour drift can be very conspicuous can be colour adjusted independently. When further fine adjustments are required, each point on the screen can be measured using an optional external colour sensor to correct the screen automatically as well.

The built-in standalone calibration function enables calibration by connecting an optional calibration sensor to the display without using a PC or dedicated application. The display also has a “white copy” function, which automatically configures to near image quality based on the white colour of adjacent screens, which can make colour matching fast even when you do not know the reference colours.

Brilliant images are reproduced naturally through HDR signal input support
The built-in HDMI terminals support the display of HDR signals (Hybrid Log method and PQ method)*. Reproduction is natural even with images with large light and darkness differences. Furthermore, HDR gamma and colour gamut can be configured manually for incompatible terminals.

The built-in HDMI and DisplayPort input and output terminals support up to 4K video for faithful display of ultrahigh resolution video
The built-in HDMI and DisplayPort input and output terminals support 4K video QFHD (3840×2160) signals. High-resolution 4K image daisy chaining is supported, resulting in an impressively large screen that does not spoil the quality of 4K video, even in a multiscreen setup.

A simple tile matrix configuration that reduces troublesome setting operations for each display
If daisy-chain connections are used for the image and control cables between all of the displays in a multiscreen setup, it is possible to press the execution button on one display and configure the remaining displays, which can simplify configuration for multiscreen setups.

The frame compensation function and vertical scan reverse function prevent image shifts that are characteristic of multiscreen setups
These two functions improve the image shift (misalignment) between displays joined in columns, which occurs when playing back high-speed video on a multiscreen setup. Frame compensation adjusts the image display timing of each frame, and the vertical scan reverse function inverts the image scan orientation of displays joined in columns alternatively, resulting in a natural video display.

Advanced heat management
Monitoring and managing the temperature of each display is crucial to secure reliability and longevity. An industrial-strength, premium-grade panel with additional thermal protection, internal temperature sensors with self-diagnostics, and fan-based technology allows for 24/ 7 operation, and protects your display investment. NEC's advanced heat management ensures uniform heat dissipation. Without heat management displays placed higher on a wall sustain more heat.

Features

  • Optional dual expansion slots
  • Intelligent wireless data function (NFC)
  • Human sensor/auto dimming with KT-RC3
  • Scheduler w/real-time clock
  • Intelligent power management system
  • Power ON delay
  • Screen saver function
  • Aspect ratio control
  • Tile cut function
  • Control lock function
  • Metal rear cabinet with VESA Standard (FDMIv1) Mounting Interface
  • Handles
  • 6-axis color adjustments and sRGB standard
  • Advanced video settings
    (Noise reduction, adaptive contrast)
  • Color temperature adjustment
  • Programmable gamma setting (3 settings)
  • DICOM SIM
  • Plug and Play (DDC/CI, DDC2B)
  • HDCP (High-bandwidth Digital Content Protections
  • NaViSet Administrator 2
  • Ethernet and RS-232C control and communication
  • Crestron RoomView
  • AMX Discovery HTTP server
  • PJLink
  • Proof of play
  • Self-diagnosis
  • Status log function
  • Firmware update by LAN

Specifications

MODEL UN552S UN552VS UN552 UN552V UN552A UX552S UX552
LCD MODULE  
Viewable size
(diagonal)
55" / 1,388 mm
Active screen area
(W × H)
1,209.63 × 680.34 mm 1,209.60 × 680.40 mm
Panel technology IPS SVA
Native resolution 1920 x 1080
Brightness
(maximum @25°C)
700 cd/m2 500 cd/m2 700 cd/m2 500 cd/m2 700 cd/m2 700 cd/m2 700 cd/m2
Contrast ratio
(typical)
1100:1 1200:1 (TBD) 4000:1
Colour
(depending on display card used)
Over 1073 million colours Over 16 million colors
Viewing angle 178° (typical) @ CR>10
Response time
(typical)
8 ms (G to G)
CONECTIVITY  
Input
terminals
DisplayPort DisplayPort x 2 (daisy chain x 1)
HDMI HDMI x 2 (daisy chain x 1, CEC x 1)
DVI-D DVI-D x 1
VGA Mini D-sub 15 pin × 1 (can be used with an RGB or YPbPr)
Video RCA × 1 (composite video)
Audio Digital: DisplayPort × 2, HDMI x 2, Analog: 3.5 mm stereo mini jack × 2
Output
terminals
DisplayPort DisplayPort x 1 (output from DisplayPort1 or option)
HDMI HDMI x 1 (output from HDMI1, DVI-D, or option)
Audio Analog: 3.5 mm stereo mini jack × 1 (output from AUDIO 1/2, DisplayPort and HDMI)
External speaker 15 W + 15 W (8 ohm)
External
control
RS232C D-Sub 9 pin × 1
Ethernet RJ-45 10BASE-T / 100BASE-TX × 2 (In/out)
Remote in 3.5 mm stereo mini jack × 1 (remote control, room light sensing and human sensing)
Remote out Possible via Ethernet
USB ports Upstream USB Type B × 1
Downstream USB Type A × 1 (colour sensor)
Power supply USB Type A 5V / max. 2A × 1
Media player USB Type A × 1
Service USB Type A × 1
Redundant external
power supply
- Connector × 1
Option slot                   Expansion slots Open pluggable specification (OPS standard) × 1, microSD/SDHC card × 1, interface extension × 1       
POWER  
Power requirement
@ 100 - 240 V
4.7 A-1.9 A 4.7 A-1.9 A 4.2 A-1.7 A 3.6 A-1.4 A 4.9 A-1.9 A 4.3 A-1.7 A 4.9 A-1.9 A
Power consumption
(Typical@factory setting)
165 W 165 W 150 W 110 W 195 W 130 W 195 W
Power consumption -
Network standby mode
2 W
ower consumption -
Standby mode
0.5 W
PHYSICAL
SPECIFICATIONS
 
Non-
display area
Top/bottom 0.44 mm*1 2.45/1.35 mm 2.5/1.4 mm 1.3/0.7 mm
*1
2.5/1.4 mm
Left/right 0.44 mm*1 2.45/1.35 mm 2.5/1.4 mm 1.3/0.7 mm
*1
2.5/1.4 mm
Dimensions Width 1210.5 mm 1213.4 mm 1213.5 mm 1211.6 mm 1213.5 mm
Height
(w/o stand)
681.2 mm   684.2 mm 684.3 mm 682.4 mm 684.3 mm
Depth
(w/o handle)
98.6 mm 103.8 mm 100.3 mm 99.7 mm 100.3 mm
Packaging
dimensions
Width 1436 mm
Height 873 mm
Depth 317 mm
Net weight 25.8 kg 28.1 kg
(TBD)
28.5 kg 29.6 kg 29.3 kg
Gross weight (with box) 37.0 kg 38 kg
(TBD)
38.3 kg TBD kg 39.1 kg
VESA hole configuration 400 × 400 mm (M6, 4 holes)
Supported orientation Landscape, portrait
ENVIRONMENTAL CONDITIONS  
Operating temperature 0 - 40° C*2
Operating humidity 20 - 80 % (without condensation)
Operating altitude 0 - 3000 m (Brightness may decrease with altitude)
Operating hours 24/7
ACCESSORIES  
Included Contents sheet and setup manual, DisplayPort cable, HDMI cable, LAN cable, Power cord,
SD card cover, Screws with washers,   
Wall mount adapters, Wall mount adapter screws, Thumbscrews for optional stands*3,
Clamp(s)*3, Spacers*3, screw for KT-RC3*3
Options  
Slot board OPS controller(PC) N8000-8866 (Core i5 60GB-SSD), N8000-8865 (Core i5 320GB-HDD)
HDBaseT SB-07BC
SDI board SB-04HC (3G-SDI)
Interface kit DS1-IF10CE (Raspberry Pi interface kit)
Remote and sensor kit KT-RC3 (IR remote unit and human, ambient light sensor kit)*4
Wall mount kit
(Landscape/portrait)
WM-55UN-L/WM-55UN-P
Over frame bezel kit - KT-55UN-OF2 - KT-55UN-OF2
Speaker SP-RM1, SP-TF1
Stand ST-5220

MODEL UN492S UN492VS UN462A UN462VA
LCD MODULE  
Viewable size
(diagonal)
49" / 1,232 mm 46" / 1,168.1 mm
Active screen area
(W × H)
1,073.78 × 604.00 mm 1,018.08 × 572.67 mm
Panel technology IPS SVA
Native resolution 1920 x 1080
Brightness
(maximum @25°C)
700 cd/m2 500 cd/m2 700 cd/m2 500 cd/m2
Contrast ratio
(typical)
1100:1 3500:1
Colour
(depending on display card used)
Over 1073 million colours Over 16 million colours
Viewing angle 178° (typical) @ CR>10
Response time
(typical)
8 ms (G to G)
CONECTIVITY  
Input
terminals
DisplayPort DisplayPort x 2 (daisy chain x 1)   
HDMI HDMI x 2 (daisy chain x 1, CEC x 1)    
DVI-D DVI-D x 1
VGA Mini D-sub 15 pin × 1 (can be used with an RGB or YPbPr)    
Video RCA × 1 (composite video)    
Audio Digital: DisplayPort × 2, HDMI x 2, Analog: 3.5 mm stereo mini jack × 2    
Output
terminals
DisplayPort DisplayPort x 1 (output from DisplayPort1 or option)    
HDMI HDMI x 1 (output from HDMI1, DVI-D, or option)    
Audio Analog: 3.5 mm stereo mini jack × 1 (output from AUDIO 1/2, DisplayPort and HDMI)    
External speaker 15 W + 15 W (8 ohm)    
External
control
RS232C D-Sub 9 pin × 1    
Ethernet RJ-45 10BASE-T / 100BASE-TX × 2 (In/out)    
Remote in 3.5 mm stereo mini jack × 1 (remote control, room light sensing and human sensing)    
Remote out Possible via Ethernet    
USB ports Upstream USB Type B × 1    
Downstream USB Type A × 1 (colour sensor)    
Power supply USB Type A 5V / max. 2A × 1    
Media player USB Type A × 1    
Service USB Type A × 1    
Redundant external
power supply
-
Option slot                   Expansion slots Open pluggable specification (OPS standard) × 1,
microSD/SDHC card × 1, interface extension × 1  
POWER  
Power requirement
@ 100 - 240 V
3.6 A - 1.5 A 3.2 A - 1.3 A 4.0 A - 1.6 A 3.4 A - 1.4 A
Power consumption
(Typical@factory setting)
120 W 95 W 125 W 90 W
Power consumption -
Network standby mode
2 W
ower consumption -
Standby mode
0.5 W
PHYSICAL
SPECIFICATIONS
 
Non-
display area
Top/bottom 0.9 mm 2.5/1.4 mm
Left/right 0.9 mm 2.5/1.4 mm
Dimensions Width 1075.6 mm 1022.0 mm
Height
(w/o stand)
605.8 mm 576.6 mm
Depth
(w/o handle)
99.0 mm 101.3 mm
Packaging
dimensions
Width 1298 mm 1221 mm
Height 795 mm 766 mm
Depth 317 mm 300 mm
Net weight 24.3 kg 21.4 kg
Gross weight (with box) 32.2kg 29.1 kg
VESA hole configuration  300 × 300 mm (M6, 4 holes)
Supported orientation Landscape, portrait
ENVIRONMENTAL CONDITIONS  
Operating temperature 0 - 40° C*2
Operating humidity 20 - 80 % (without condensation)
Operating altitude 0 - 3000 m (Brightness may decrease with altitude)
Operating hours 24/7
ACCESSORIES  
Included Contents sheet and setup manual, DisplayPort cable, HDMI cable, LAN cable, Power cord,
SD card cover, Screws with washers,
Wall mount adapters, Wall mount adapter screws, Thumbscrews for optional stands*3,
Clamp(s)*3, Spacers*3, screw for KT-RC3*3
Options  
Slot board OPS controller(PC) N8000-8866 (Core i5 60GB-SSD), N8000-8865 (Core i5 320GB-HDD)
HDBaseT SB-07BC
SDI board SB-04HC (3G-SDI)
Interface kit DS1-IF10CE (Raspberry Pi interface kit)
Remote and sensor kit KT-RC3 (IR remote unit and human, ambient light sensor kit)*4
Wall mount kit
(Landscape/portrait)
WM-49UN-L WM-46UN-L3/WM-46UN-P2
Over frame bezel kit KT-49UN-OF KT-46UN-OF5
Speaker SP-RM1, SP-TF1
Stand ST-322

Selv om vi gjør vårt beste for å gi relevant informasjon, så er bildene kun for å gi et generelt inntrykk, og selve varen er ikke nødvendigvis akkurat slik som avbildet. Dersom det er forskjeller mellom produktoverskrift, beskrivelse og bilde, så er det produktoverskriften som gjelder (f.eks. PCer kommer ikke nødvendigvis med skjerm selv om bildet viser det). Hvis noe er uklart, vennligst send epost til kundestøtte før du bestiller. Vi tar forbehold om trykkfeil og endring av priser og spesifikasjoner uten varsel.
Copyright 2023 Kinly. All rights reserved.